New for 2020 is the full carbon, low profile FoilMount 3.0 Carbon.

This compressed carbon plate is not only beautiful it is also incredibly strong allowing it to be thinner than the original FoilMount.  This setup weighs just over 1lb so it is also about 30% lighter than previous models.  The new curved shape along with its light weight and thinner profile make it incredibly low drag in the water.  You cannot tell there is a track mounted on the bottom of your board while using it without a hydrofoil.  We have also upgraded the included hardware.  Because this system is so thin, we had to invent a new hardware set that would work with any base plate on the market called the Wizardhat Hardware.  Each FoilMount 3.0 Carbon includes a set of 4 Wizardhat hardware and they will allow you to attach any hydrofoil on the market to your FoilMount.  

Wizardhat Hardware Set

This is the Wizardhat hardware set.  If you just need some extra hardware

This hardware set will work with any base plate or 4-bolt tracked board on the market.  This included M8 or M6 base plates and tracks.  There is no more need for T-nuts or different sized bolts the Wizardhat will work on any.  Also, the way the bolt sticks up through the track on top makes it easy to line up with the base plate.

The Wizardhat hardware only set comes with 4 qty Wizardhat hardware (includes cone nut, t-bolt, and t-slider with a decal.  

*Be careful not to over- tighten with the wrench as you will have a lot more leverage than the screwdrivers you have been using.

PKS M6 Studs for mounting Hydrofoil on deck with inserts.

Works with M6 Inserts and m6 hardware like the Wizard Hat Cone nuts.

Includes a set of 4 M6 Studs

PKS M6 Studs for mounting Hydrofoil on deck with inserts.

Works with M6 Inserts and m6 hardware like the Wizard Hat Cone nuts.

Includes a set of 4 M6 Studs

Wizardhat Cone Nut Set with m6x25mm Studs

This is the Wizardhat Cone Nuts with m6 x 25mm Studs.  If you just need some extra hardware.

Includes a set of 4 Cone Nuts with m6 x 25mm Studs

Wizardhat Hardware Set

This is the Wizardhat hardware only set.  If you just need some extra hardware

This hardware set will work with any base plate or 4-bolt tracked board on the market.  This included M8 or M6 base plates and tracks.  There is no more need for T-nuts or different sized bolts the Wizardhat will work on any.  Also, the way the bolt sticks up through the track on top makes it easy to line up with the base plate.

The Wizardhat hardware only set comes with 4 qty Wizardhat hardware (includes cone nut, t-bolt, and t-slider with a decal.   

*Be careful not to over- tighten with the wrench as you will have a lot more leverage than the screwdrivers you have been using.

M6 Hydrofoil Track Stainless Steel T-Nuts

These are Replacement M6 Stainless Steel T-nuts for any hydrofoil that uses the M6 T-nut including Takuma, Naish and others  These are hard to get replacements that we now have in stock.  They are sold individually, so if you need a set of 4 make sure to buy 4 of them.  Watch the video below for our testing of the M8 version against the brass version.

Here are the total dimensions of this part:

Track width: 8.5mm
Total width: 14.9mm
Total length: 23.9mm
Total height: 6.20mm

M6 Hydrofoil Track Stainless Steel T-Nuts and M6 Mounting Screws - Set

These are Replacement M6 Stainless Steel T-nuts and M6 Mounting Screws for any hydrofoil that uses the M6 T-nut including Takuma, Naish and others. These are hard to get replacements that we now have in stock.  They are sold as a complete set.

Here are the total dimensions of the track nuts:
Track width: 8.5mm
Total width: 14.9mm
Total length: 23.9mm
Total height: 6.20mm

Mounting Screws are M6 Socket Head Screws

M6 Hydrofoil Mounting Screws

These are M6 Stainless Steel screws for any hydrofoil that uses the M6 T-nut, which which will work on all M6 Tracked hydrofoils.  These are Hex Head (socket cap), counter sink screws

Sold individually

M8 Hydrofoil Track Stainless Steel T-Nuts

These are low profile replacement M8 Stainless Steel T-nuts for any hydrofoil that uses the M8 T-nut, which just about all Tracked hydrofoils.  These are low profile meaning they are thinner than stock brass T-nuts by about 2.2mm from top to bottom but STRONGER.

M8 Hydrofoil Track Brass T-Nuts

Extra brass T-nuts for your tracked hydrofoil.  These are salt water approved and perfect for all track systems.  They are M8 standard metric threads which is the convention for most hydrofoil tracks.

Sold Individually

M8 Hydrofoil Brass Track T-Nuts and Stainless Steel M8 x 25mm Mounting Screws - Set

These are Replacement M8 Stainless Steel T-nuts and M8 x 25mm Mounting Screws for any hydrofoil that uses the M8 T-nut including Slingshot, Duotone, North and many others. These are hard to get replacements that we now have in stock.  They are sold as a complete set.

Here are the total dimensions of the track nuts:
15mm width
19mm length
8.5mm height
8.6mm width of center section with threads
3.95mm height from bottom of step

Mounting Screws are M8 x 25mm Socket Head Screws

These are M8 Stainless Steel screws for any hydrofoil that uses the M8 T-nut, which just about all Tracked hydrofoils.  These are Hex Head (socket cap), counter sink screws

Sold individually

M8 Hydrofoil Track Stainless Steel T-Nuts and M8 x 25mm Mounting Screws - Set

These are Replacement M8 Stainless Steel T-nuts and M8 x 25mm Mounting Screws for any hydrofoil that uses the M8 T-nut including Takuma, Naish and others. These are hard to get replacements that we now have in stock.  They are sold as a complete set.

Mounting Screws are M8 x 25mm Socket Head Screws